HDL2-Aの起動ログ (r27866-1728d212d7)

from HDL2-A

code:boot.log

============================================================

HDL2-A series Initial boot loader

============================================================

** LOADER **

** MARVELL BOARD: HDL2A LE

U-Boot 1.1.4 (Nov 8 2011 - 14:25:31) MV : 3.5.9 I-O : 1.07

U-Boot code: 00600000 -> 0066FFF0 BSS: -> 006BDAE0

Soc: 88F6282 A1CPU running @ 1600Mhz L2 running @ 533Mhz

SysClock = 533Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7

DRAM CS0 base 0x00000000 size 256MB

DRAM Total size 256MB 16bit width

Addresses 8M - 0M are saved for the U-Boot usage.

Mem malloc Initialization (8M - 7M): Done

512kB@f8000000 Flash: 512 kB

CPU : Marvell Feroceon (Rev 1)

Streaming disabled

Write allocate disabled

USB 0: host mode

PEX 0: interface detected no Link.

PEX 1: interface detected no Link.

Net: egiga0 PRIME

Reset IDE:

Marvell Serial ATA Adapter

Integrated Sata device found

** Bad partition 1 **

(Re)start USB...

USB: scanning bus for devices... 3 USB Device(s) found

Waiting for storage device(s) to settle before scanning...

1 Storage Device(s) found

** Partition 0 not valid on device 0 **

** Unable to use usb 0:0 for fatload **

reading l2a/uImage.l2a

..........................................................................................................

.......................................................

5999073 bytes read

reading l2a/initrd.l2a

64 bytes read

## Starting secure boot ...

## Starting application at 0x00100000 ...

## Application terminated, rc = 0x0

................

## Booting image at 00800000 ...

Image Name: ARM OpenWrt Linux-6.6.57

Image Type: ARM Linux Kernel Image (uncompressed)

Data Size: 5999009 Bytes = 5.7 MB

Load Address: 00008000

Entry Point: 00008000

Verifying Checksum ... OK

Starting kernel ...

0.000000 Booting Linux on physical CPU 0x0

0.000000 Linux version 6.6.57 (miminashi@akdx01) (arm-openwrt-linux-muslgnueabi-gcc (OpenWrt GCC 13.

3.0 r27866-1728d212d7) 13.3.0, GNU ld (GNU Binutils) 2.42) #0 Mon Oct 21 07:52:24 2024

0.000000 CPU: Feroceon 88FR131 56251311 revision 1 (ARMv5TE), cr=0005397f

0.000000 CPU: VIVT data cache, VIVT instruction cache

0.000000 OF: fdt: Machine model: I-O DATA HDL2-A (USB)

0.000000 earlycon: ns16550a0 at MMIO 0xf1012000 (options '115200n8')

0.000000 printk: bootconsole ns16550a0 enabled

0.000000 Memory policy: Data cache writeback

0.000000 Zone ranges:

0.000000 Normal mem 0x0000000000000000-0x000000000fffffff

0.000000 Movable zone start for each node

0.000000 Early memory node ranges

0.000000 node 0: mem 0x0000000000000000-0x000000000fffffff

0.000000 Initmem setup node 0 mem 0x0000000000000000-0x000000000fffffff

0.000000 Kernel command line: console=ttyS0,115200 mtdparts=spi_flash:448k(u-boot),64k@448k(env) roo

t=/dev/md2 initrd=0x2000040,16M rw model=HDL2-A/H earlycon root=PARTUUID=5452574f-02 rootwait=20

0.000000 Unknown kernel command line parameters "mtdparts=spi_flash:448k(u-boot),64k@448k(env) model

=HDL2-A/H", will be passed to user space.

0.000000 Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear)

0.000000 Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear)

0.000000 Built 1 zonelists, mobility grouping on. Total pages: 64960

0.000000 mem auto-init: stack:off, heap alloc:off, heap free:off

0.000000 Memory: 222884K/262144K available (6877K kernel code, 590K rwdata, 1764K rodata, 10240K ini

t, 208K bss, 39260K reserved, 0K cma-reserved)

0.000000 SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1

0.000000 NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16

0.000000 clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 95563

02233 ns

0.000001 sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns

0.007813 Switching to timer-based delay loop, resolution 5ns

0.013797 Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS

(lpj=2000000)

0.024304 CPU: Testing write buffer coherency: ok

0.029268 pid_max: default: 32768 minimum: 301

0.042305 Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)

0.049615 Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)

0.064890 RCU Tasks Trace: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1.

0.072653 Setting up static identity map for 0x100000 - 0x10003c

0.079049 mvebu-soc-id: MVEBU SoC ID=0x6282, Rev=0x1

0.089093 clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 191126044627500

00 ns

0.098921 futex hash table entries: 256 (order: -1, 3072 bytes, linear)

0.107869 pinctrl core: initialized pinctrl subsystem

0.114989 NET: Registered PF_NETLINK/PF_ROUTE protocol family

0.121727 DMA: preallocated 256 KiB pool for atomic coherent allocations

0.129712 thermal_sys: Registered thermal governor 'step_wise'

0.129757 cpuidle: using governor ladder

0.140161 Feroceon L2: Enabling L2

0.143746 Feroceon L2: Cache support initialised.

0.152143 No ATAGs?

0.161675 SCSI subsystem initialized

0.165843 usbcore: registered new interface driver usbfs

0.171348 usbcore: registered new interface driver hub

0.176661 usbcore: registered new device driver usb

0.182750 clocksource: Switched to clocksource orion_clocksource

0.197694 NET: Registered PF_INET protocol family

0.202711 IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)

0.210711 tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 4096 bytes, linear)

0.219144 Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)

0.226862 TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear)

0.234516 TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear)

0.241664 TCP: Hash tables configured (established 2048 bind 2048)

0.248073 UDP hash table entries: 256 (order: 0, 4096 bytes, linear)

0.254598 UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)

0.262087 NET: Registered PF_UNIX/PF_LOCAL protocol family

0.267764 PCI: CLS 0 bytes, default 32

0.302890 workingset: timestamp_bits=14 max_order=16 bucket_order=2

0.321904 squashfs: version 4.0 (2009/01/31) Phillip Lougher

Inc.

0.376315 kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver

0.384455 gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation.

0.393812 gpio gpiochip1: Static allocation of GPIO base is deprecated, use dynamic allocation.

0.403257 Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled

0.410391 printk: console ttyS0 disabled

0.414901 f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 12500000) is a 16550A

0.423868 printk: console ttyS0 enabled

0.432261 printk: bootconsole ns16550a0 disabled

0.465278 Unpacking initramfs...

0.468712 Initramfs unpacking failed: invalid magic at start of compressed archive

0.523392 Freeing initrd memory: 16388K

0.528512 f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 26, base_baud = 12500000) is a 16550A

0.542144 loop: module loaded

0.545977 sata_mv f1080000.sata: slots 32 ports 2

0.572164 scsi host0: sata_mv

0.576493 scsi host1: sata_mv

0.579826 ata1: SATA max UDMA/133 irq 27

0.583966 ata2: SATA max UDMA/133 irq 27

0.593384 spi-nor spi0.0: w25x40 (512 Kbytes)

0.604367 2 fixed-partitions partitions found on MTD device spi0.0

0.610765 Creating 2 MTD partitions on "spi0.0":

0.615601 0x000000000000-0x000000070000 : "u-boot"

0.621839 0x000000070000-0x000000080000 : "u-boot-env"

0.644378 mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4

0.655242 mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:a0:b0:f2:6a:2f

0.664307 orion-ehci f1050000.ehci: EHCI Host Controller

0.669839 orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1

0.677692 orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000

0.712761 orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00

0.719588 hub 1-0:1.0: USB hub found

0.723739 hub 1-0:1.0: 1 port detected

0.728054 usbcore: registered new interface driver usb-storage

0.734256 i2c_dev: i2c /dev entries driver

0.739993 orion_wdt: Initial timeout 21 sec

0.751134 marvell-cesa f1030000.crypto: CESA device successfully registered

0.759647 NET: Registered PF_INET6 protocol family

0.766714 Segment Routing with IPv6

0.770472 In-situ OAM (IOAM) with IPv6

0.774560 NET: Registered PF_PACKET protocol family

0.779652 8021q: 802.1Q VLAN Support v1.8

0.818951 clk: Disabling unused clocks

0.914822 ata1: SATA link down (SStatus 0 SControl F300)

1.022760 usb 1-1: new high-speed USB device number 2 using orion-ehci

1.223942 hub 1-1:1.0: USB hub found

1.228098 hub 1-1:1.0: 2 ports detected

1.243136 ata2: SATA link down (SStatus 0 SControl F300)

1.278266 Freeing unused kernel image (initmem) memory: 10240K

1.284350 Run /init as init process

1.553118 usb 1-1.2: new high-speed USB device number 3 using orion-ehci

1.580691 init: Console is alive

1.584375 init: - watchdog -

1.593530 kmodloader: loading kernel modules from /etc/modules-boot.d/*

1.603867 rtc-rs5c372 0-0032: rs5c372a found, 24hr

1.610727 rtc-rs5c372 0-0032: registered as rtc0

1.617351 rtc-rs5c372 0-0032: hctosys: unable to read the hardware clock

1.627944 kmodloader: done loading kernel modules from /etc/modules-boot.d/*

1.638068 init: - preinit -

1.745845 usb-storage 1-1.2:1.0: USB Mass Storage device detected

1.776841 scsi host2: usb-storage 1-1.2:1.0

3.082789 random: crng init done

Cannot parse config file '/etc/fw_env.config': No such file or directory

Failed to find NVMEM device

Press the f key and hit enter to enter failsafe mode

Press the 1, 2, 3 or 4 key and hit enter to select the debug level

3.438349 scsi 2:0:0:0: Direct-Access BUFFALO USB Flash Disk 1.00 PQ: 0 ANSI: 6

3.449205 sd 2:0:0:0: sda 30965760 512-byte logical blocks: (15.9 GB/14.8 GiB)

3.458333 sd 2:0:0:0: sda Write Protect is off

3.464448 sd 2:0:0:0: sda No Caching mode page found

3.469791 sd 2:0:0:0: sda Assuming drive cache: write through

3.482350 sda: sda1

3.484977 sd 2:0:0:0: sda Attached SCSI removable disk

5.989468 mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control dis

abled

7.367059 procd: - early -

7.370087 procd: - watchdog -

7.917574 procd: - watchdog -

7.920978 procd: - ubus -

7.977154 procd: - init -

Please press Enter to activate this console.

8.108439 urngd: jent-rng init failed, err: 11

8.293931 kmodloader: loading kernel modules from /etc/modules.d/*

8.339704 xt_time: kernel timezone is -0000

8.384638 kmodloader: done loading kernel modules from /etc/modules.d/*

16.472359 br-lan: port 1(eth0) entered blocking state

16.477648 br-lan: port 1(eth0) entered disabled state

16.482936 mv643xx_eth_port mv643xx_eth_port.0 eth0: entered allmulticast mode

16.490440 mv643xx_eth_port mv643xx_eth_port.0 eth0: entered promiscuous mode

19.135933 mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control ena

bled

19.145781 br-lan: port 1(eth0) entered blocking state

19.151035 br-lan: port 1(eth0) entered forwarding state

BusyBox v1.36.1 (2024-10-21 07:52:24 UTC) built-in shell (ash)

_______ ________ __

| |.-----.-----.-----.| | | |.----.| |_

| - || _ | -__| || | | || _|| _|

|_______|| __|_____|__|__||________||__| |____|

|__| W I R E L E S S F R E E D O M

-----------------------------------------------------

OpenWrt SNAPSHOT, r27866-1728d212d7

-----------------------------------------------------

=== WARNING! =====================================

There is no root password defined on this device!

Use the "passwd" command to set up a new password

in order to prevent unauthorized SSH logins.

--------------------------------------------------

root@OpenWrt:~#